IMEI numbers and de/pre-registration
I am now (after upgrading) sending data but I don’t see it in the portal.
I copy/pasted the IMEI number from the AT command so I am sure it is the correct one. But I thought - maybe it was pre-registered because I know on the sodaq forum they imply pre-registration.
Does anyone know if I can see if my IMEI number was already pre-registered and if this is the case , can I de-register.
Also if it was pre-registered and I register it again in my portal , does the data get split and sent to both portal accounts or will I never see the data until I de-register it elsewhere.
Just to be clear , I am using a sketch that I installed on an already upgraded board and it is working , so I have one IMEI registered in my account and it is receiving data perfectly , so I know it is not a software issue
Here is some debug from my sketch
OK[rdResp]: OK [rdResp]: timed out >> AT+NMGS=11,"48656c6c6f20576f726c64" OK[rdResp]: OK +NSMI: SENT[rdResp]: +NSMI: SENT [rdResp]: timed out >> AT+NQMGS PENDING=0,SENT=36,ERROR=0[rdResp]: PENDING=0,SENT=36,ERROR=0 OK[rdResp]: OK [rdResp]: timed out >> AT+NUESTATS "Signal power",-737[rdResp]: "Signal power",-737 "Total power",-673[rdResp]: "Total power",-673 "TX power",-70[rdResp]: "TX power",-70 "TX time",4721[rdResp]: "TX time",4721 "RX time",658691[rdResp]: "RX time",658691 "Cell ID",49702501[rdResp]: "Cell ID",49702501 "ECL",0[rdResp]: "ECL",0 "SNR",144[rdResp]: "SNR",144 "EARFCN",3747[rdResp]: "EARFCN",3747 "PCI",135[rdResp]: "PCI",135 "RSRQ",-108[rdResp]: "RSRQ",-108 OK[rdResp]: OK [rdResp]: timed out
If it’s a Sodaq device, then your IMEI is already registered in the application which Sodag has on our IoT-network. So this should be the reason why your data is not coming through.
By entering your IMEI no. in your devreg.iot.t-mobile.nl portal, you registered the IMEI in your own application on our IoT-network. Hence, there is a double registration right now so no one is able to receive the data.
Please send me a direct message with your IMEI number, I can remove the registration in the Sodaq environment. Or you ca nask Sodaq to remove it.
I tried it and I get this error on sending >
+CME ERROR: 513[rdResp]: +CME ERROR: 51
is this because I have to no re-register it?
Not sure to be honest. Have you already tried to remove it in the devreg-tool en re-register it?
By the way, where did you register your device exactly? I was not able to find an account on your e-mailaddress…
@afzal_m I am doing a project for Adriaan van Eck, so I amusing his portal on
Ah, ok then I can confirm that there is nothing wrong with the application.
Please let me know what happens after re-registering (removing en adding the IMEI).
@afzal_m will do
@jonathan-carter still the same
I also get no success or failure from the module either
@jonathan-carter I have a CSQ of
and a STATS of :
>> AT+NUESTATS "Signal power",-829[rdResp]: "Signal power",-829 "Total power",-720[rdResp]: "Total power",-720 "TX power",20[rdResp]: "TX power",20 "TX time",11725[rdResp]: "TX time",11725 "RX time",311912[rdResp]: "RX time",311912 "Cell ID",2362982[rdResp]: "Cell ID",2362982 "ECL",1[rdResp]: "ECL",1 "SNR",19[rdResp]: "SNR",19 "EARFCN",3747[rdResp]: "EARFCN",3747 "PCI",352[rdResp]: "PCI",352 "RSRQ",-131[rdResp]: "RSRQ",-131 OK[rdResp]: OK
@jonathan-carter I looked up error 513 in the U-blox datasheets and it is :
513 Module not registered
What I noticed yesterday (in your post with the IMEI), was that the last digit was missing.
And I also see another thing that is causing an issue (and also an improvement for our manuals, thanks!): there are some spaces and brackets in your device name.
So the best thing to do is:
- Delete both devices (ave … and jc …)
- Double check the IMEI (should be 15 digits)
- Register it with a simple device name (alphanumeric)
Please let me know if this works!
@afzal_m attempting now
@afzal_m BINGO!!! it works
@afzal_m here is another address to “delete” from the pre-registration of SODAQ